Hits: 1720 img
IOTA LSR 3050 A/B is a high-transparency liquid silicone rubber with self-adhesive properties to PC and good mold release. Main features include two-component 1:1 mixing ratio, excellent mold release, excellent transparency, outstanding self-adhesion to PC, fast heat curing, and excellent mechanical properties. Applications include swim goggle sealing, phone protective case overmolding, smartwatch back cover seals, and phone SIM tray seals.
Technical data: Component A viscosity 300 Pa·s and Component B viscosity 400 Pa·s (after stirring at 23°C); A+B mixture viscosity 350 Pa·s; mixing ratio 1:1 by weight. After curing (23±2°C, 24 h vulcanization): density 1.13 g/cm³ (ISO 2781), Shore A hardness 50, tensile strength 10.0 MPa, elongation 550%, and tear strength 35 kN/m. The curing time section only says “see curing conditions” and does not give a specific temperature-time table; actual curing conditions should be obtained from the supplier or confirmed with the equipment and product structure.
Selection should not rely only on “self-adhesive to PC,” “high transparency,” or “hardness 50.” First confirm the PC grade and surface condition, overmolding structure and insert method, mold and release requirements, same-batch A/B 1:1 metering and mixing, whether fillers are thoroughly stirred, curing temperature and time, target film thickness, and the project acceptance criteria for adhesion, transparency, release, mechanical properties, and sealing/waterproofing. This article does not equate “self-adhesive to PC” with self-adhesion to all plastics, nor does it apply the 23°C/24 h vulcanization conditions to all thicknesses and structures. The data describe high transparency but give no transmittance value, so it should be confirmed separately on the target film thickness and substrate. IOTA can provide liquid silicone rubber raw materials and corresponding product data; the company does not provide complete formulations or formulation development services.
The product is used for PC self-adhesion, phone protective case overmolding, swim goggle sealing, smartwatch back cover seals, and phone SIM tray seals. Different applications focus on different points: phone case overmolding on PC adhesion, transparency, and appearance; swim goggle sealing on softness, sealing, and water resistance; watch back cover seals on compression set and dimensional stability; SIM tray seals on assembly precision and release. Selection should start with the PC grade, overmolding structure, insert method, and target defect, not just “self-adhesive transparent silicone.”
| What to confirm | What to specify in an inquiry or sample request |
|---|---|
| PC substrate and pretreatment | PC grade, surface condition, whether primer is applied, cleaning method, whether flame or plasma treatment is used |
| Overmolding structure and mold | Overmolding area, insert fixing method, mold material, release method, whether release agent is used |
| Mixing and metering | Two-component A:B = 1:1; only same-batch A/B may be mixed; metering accuracy, mixing uniformity, and application pace |
| Material pretreatment | Whether thoroughly stirred before transfer to container so fillers that may settle during storage are uniformly dispersed |
| Curing conditions | Curing temperature and time; the data only say “see curing conditions,” so obtain from the supplier and confirm with product thickness and equipment |
| Acceptance criteria | Adhesion to PC, transparency, release, hardness, tensile strength, tear strength, elongation, compression set, sealing/waterproofing performance, etc. |
| Sample preparation | Sample size, PC batch, overmolding area, vulcanization conditions, secondary heating, whether evaluated after aging or water exposure, sample quantity |
If the customer already has a test specification, obtain the original document first. When criteria are missing, confirm them with the project owner and test laboratory before making samples, so that both sides do not discover different interpretations of “pass” after testing.
IOTA LSR 3050 uses a two-component 1:1 mixing ratio. Important notes: the product is platinum-catalyzed, with the platinum catalyst in Component A; strict care is required during use to avoid catalyst poisoning. Only Component A and Component B of the same batch number may be mixed together. To ensure optimum flow and uniformity, the material must be thoroughly stirred before transfer into a container so that fillers that may settle during storage are uniformly dispersed.
The curing time section only says “see curing conditions” and does not provide a specific temperature-time table. Therefore, sample-request and acceptance documents should not simply apply conditions from other series. Obtain the current batch curing recommendation from the supplier and confirm it with the overmolding structure, PC heat tolerance, and equipment. The cured property data correspond to 23±2°C and 24 h vulcanization and should also be checked against the actual vulcanization conditions of the target product. Insufficient stirring can affect flow, transparent appearance, and final property consistency at the same time.
The product data state outstanding self-adhesion to PC. Self-adhesion depends on PC grade, surface condition, cleaning method, overmolding area, insert fixing, mold temperature, and vulcanization conditions. Different PC grades (such as standard PC, flame-retardant PC, and glass-fiber-reinforced PC) differ in surface properties and heat tolerance; adhesion results on one PC grade cannot be used to infer other PC grades. For other plastics, adhesion should be evaluated separately; “self-adhesive to PC” cannot be extrapolated to all plastics.
Mold release and self-adhesion need to be balanced: the material must adhere firmly to PC while releasing easily from the mold. Mold material, surface treatment, and whether a release agent is used all affect both, and should be confirmed with representative overmolding samples.
The product data state excellent transparency and high transparency, but do not give a visible-light transmittance value, so a value such as “>90%” should not be added by assumption. Transparency depends on film thickness, PC background color, vulcanization conditions, and test method, and should be confirmed separately on the target film thickness and substrate.
Shore A hardness 50 is a medium hardness range. For phone case overmolding and seals, it should be confirmed with feel, assembly force, and sealing requirements. For soft sealing scenarios such as swim goggle seals, softness, sealing performance, and water resistance should be evaluated separately, not selected by hardness alone.
“Waterproof sealing” is an application description and is not the same as having passed a specific waterproof rating or long-term water immersion test; relevant projects should be verified separately according to the corresponding specification.
Technical data: Component A viscosity 300 Pa·s, Component B 400 Pa·s, mixture 350 Pa·s (after stirring at 23°C); after curing (23±2°C, 24 h vulcanization): density 1.13 g/cm³, Shore A hardness 50, tensile strength 10.0 MPa, elongation 550%, and tear strength 35 kN/m. These are typical data under the corresponding conditions in the product data and should be understood together with overmolding structure, film thickness, vulcanization conditions, and test methods.
For phone case overmolding and watch back cover seals, compression set, dimensional stability, and media resistance should be evaluated; for swim goggle seals, water resistance, softness, and sealing retention should be evaluated. Typical tensile and tear data cannot directly represent finished-product sealing life.
Obtain the customer’s service conditions and acceptance criteria; confirm whether PC adhesion, transparency, release, mechanical properties, and sealing/waterproofing requirements are targets or existing results.
Specify PC grade and surface treatment, overmolding structure and mold, same-batch A:B = 1:1 mixing/metering, filler stirring, curing temperature and time, and post-treatment arrangement.
Check the current IOTA LSR 3050 data, then have the user make representative overmolding samples and keep records of mixing, injection, vulcanization, release, and post-treatment.
Arrange tests as agreed; keep sample identity, test conditions, observation photos, and evaluation results in the report. Before expanding use, confirm whether the samples represent actual workpieces.
IOTA/Anhui Iota Silicone Oil Co., Ltd. positions itself as a solution provider across the organosilicon industry chain and can provide liquid silicone rubber raw materials and corresponding product data. When communicating, provide the PC grade, overmolding structure, mold, curing equipment, and target defects together to facilitate candidate screening; the company does not provide complete formulations or formulation development services.
No. The data only state self-adhesive properties to PC. Other plastics have different surface properties and should be evaluated separately; direct extrapolation is not appropriate.
Not recommended. Obtain the current batch curing recommendation from the supplier and confirm it with the overmolding structure, PC heat tolerance, product thickness, and equipment.
Not necessarily. The data state high transparency and excellent transparency but give no transmittance value; test on the target film thickness and substrate using the corresponding method.
The data require thorough stirring before transfer into a container so that fillers that may settle during storage are uniformly dispersed. Insufficient stirring can affect flow, transparent appearance, and final property consistency.
The platinum catalyst is in Component A. Strict care is required during use to avoid contact with substances known to poison platinum catalysts. Specific material compatibility should be included in the customer’s raw-material approval and site management requirements.
Not necessarily. Hardness 50 is a medium hardness range; soft sealing scenarios such as swim goggle seals should be evaluated separately for softness, sealing performance, and water resistance, not selected by hardness alone.
No. Waterproof sealing is an application description. The specific waterproof rating, water exposure time, and test conditions must be verified separately according to the project specification.