Online service
Hotline
15556181299

Food grade silicone rubber for mold making

    Food grade silicone rubber for mold making

    1: 1 component liquid silicone is addition type non-toxic and tasteless liquid mold silicone rubber, can be placed in the oven pan, resistant to high temperature 250 ℃, long-term stability can be used within 200 ℃. This product pass the FDA food-grade certification, could be used to produce adult products, human organs, body parts, mannequin, chest pads, shoulder pads and other soft silicone rubber. Also used in food molds, candy molds, cake molds, as well as a good material for soap cake mold making.

     

    Appearance:

    Part A: a non-toxic and odorless liquid with translucent color and platinum inside
    Part B: a non-toxic and odorless liquid with translucent color.
    ATT: We can do any curing time as your requirements.


    Product technical data

    Item number

    Color

    Hardness(A)

    Viscosity(cps)

    Tear strength(KN/m)

    Tensile strength(Mpa)

    Elongation (%)

    Shrinkage

    (%)

    IOTA 15000

    Semi-transparent

    0

    5000±1000

    2

    2.0

    500

    0.1

    IOTA 1505

    Semi-transparent

    5±2

    5500±1000

    4

    2.5

    550

    0.1

    IOTA 1510

    Semi-transparent

    10±2

    6000±1000

    12

    3.0

    500

    0.1

    IOTA 1515

    Semi-transparent

    15±2

    8000±1000

    13

    3.2

    450

    0.1

    IOTA 1520

    Semi-transparent

    20±2

    10000±1000

    16

    3.5

    400

    0.1

    IOTA 1525

    Semi-transparent

    25±2

    15000±1000

    16

    4.0

    420

    0.1

    IOTA 1530

    Semi-transparent

    30±2

    20000±1000

    17

    4.5

    350

    0.1

    IOTA 1540

    Semi-transparent

    40±2

    22000±1000

    17

    4.5

    330

    0.1

    IOTA 1550

    Semi-transparent

    50±2

    25000±1000

    15

    4.6

    170

    0.1

    IOTA 1560

    Semi-transparent

    60±2

    45000±1000

    14

    4.8

    150

    0.1

     

    Products Procedure

    1. Mixing: The A and B rubber 1: 1 weight ratio mix and stir evenly.

    2. Discharge bulbs: For high requirements should be evacuated discharge bubbles, otherwise the mold will have bubbles.

    3. Material pouring: pour the mixing the stirred liquid silicone into the mold box.

     

    Precautions For Use

    1. Before large-scale use, please do small amount of trial, familiar with the production skills to avoid errors.

    2. Do according to the manufacturer's instructions ratio for quantity, and the weighing accuracy, please remember that the ratio is by weight rather than volume. After the mixing of AB silicone rubber, stir it fully to avoid not cure or incomplete cure.

    3. When make the mold frame, if 502 glue is applied, pour the mixing silicone rubber after half an hour or put it into oven at 50℃ for 10 minutes, to prevent 502 glue and silicone poisoning to make it not cure.

    4. To accelerate the curing time, heating method can be used to speed up the curing rate of silicone rubber.

    5. When mixing the AB silicone, mixing in the same direction. When pour glue, take a little bit of the higher and same position on the female die on the same position, let the glue flow flat on the master die, it will increase the flow time of the glue to reduce the bubble.  Generally, the silicone in hardness higher than 20, it will need to do vacuum pumping before use.

    6. 1:1 Addition products will have toxic reaction with tin, phosphorus, ammonium, chlorine, carboxylic acids, thiol, hydroxyl and other compounds. It is forbidden to contact with such compounds to avoid the occurrence of non-curing. 


Telephone:18255207206 Mobile:15556181299
Consultation
Products
Application
QQService